# Static Electricity Lab for the Classroom — The Sticky-Tape Lab

Source: https://decka.dev/classroom/physics/static-electricity-lab

Students charge strips of sticky tape by peeling one off another, seal a prediction for each of five pairs, then test the pairs at their desks. The big screen deals the room's predictions beside its readings, pair by pair, and a rubbed balloon is sorted against the two kinds of strip.

## What it teaches

Students test, with tape they charge themselves, whether like strips push apart and unlike strips pull together; work out why both kinds of strip pull an uncharged scrap of paper, which is why only a push proves that something is charged; and sort a rubbed balloon against their strips to ask whether two kinds of charge are enough.

## A static electricity lab built on the room's own tape

The lesson opens on an empty desk edge on the big screen. Each pair of students makes two pairs of charged strips from matte tape: one strip stuck to the desk and marked B on its folded tab, a second stuck on top of it and marked T, then both peeled off together and T pulled off B fast. The screen draws the steps and every phone lists them, and the strips are hung from the desk edge, apart.

Each phone then asks what five pairs will do: T near T, B near B, T near B, and each strip near a scrap of paper. Every answer is a small drawing of the pair pushed apart, pulled together or doing nothing. The predictions are sealed: the screen counts them in, and never shows what they say. Students then bring each pair close without letting the strips touch, and record what they saw while the predictions stay sealed on the screen beside the empty desk.

When the readings close, the table deals the room's predictions as hatched lanes under each pair, then its readings as solid lanes over them. Each pair of strips takes the pose most of the room saw, and under every pair with a clear answer the pen writes its rule, such as “T pushes T.” An answer is clear when it holds at least half of the pair's readings and leads the next by at least 15 points; any other pair says “No clear answer”, gets no rule, and keeps its strips at rest. Only when both strips pulled the paper does a brace join the two paper pairs, saying the paper would have to be T-kind and B-kind at once. Each phone shows its owner's own sheet: what they predicted and saw for each pair, beside the room's answer.

Next the room votes on why the paper is pulled, from four explanations of similar length, under a question worded from the room's own table. The vote's board shows how the room voted with no answer marked. When you move on, the pen ticks the answer, that the paper isn't charged and the strip shifts the paper's own charges, and a diagram shows why, with the two kinds drawn as a dot and a ring: the charges near the strip are pulled harder than the far ones are pushed. A pull doesn't prove charge; only a push does.

Last, everyone rubs a balloon on their hair or sleeve, records what it does near a T strip and near a B strip, and sorts it: like T, like B, a new kind, or can't tell. The model board deals the room's sort, then a three-by-three table of what each balloon did near T and near B, each card landing in its own box. Its corner is the box that would disprove two kinds of charge, a balloon that pushed both strips. The pen rings that count, and the board concludes that two kinds are enough only when the corner is empty and the table showed both pushes and the pull; otherwise it says why it cannot conclude that yet.

The screen shows counts only, never names, and each phone shows its owner's own answers beside the room's counts. Desk partners' two phones are two readings of one experiment, so the board counts readings, not experiments. Try the screen-and-phone preview, where your phone is one student's and fictional classmates answer through the same runtime as the lesson; they are illustrative, not observations of a real class.

## Classroom debrief

Which result surprised the room most? How far were the hatched lanes, what the room predicted, from the solid ones, what it saw?

If both strips pulled the paper, why can't that mean the paper carries the kind opposite to both?

If someone hands you a mystery strip that pulls your T strip, what do you know? What if it pushes it?

What would a third kind of charge have to do to T and B? Did anyone's balloon do that?

Some pairs show “nothing” more than others. What about the air in this room could bleed the charge away?

## Static electricity lab questions, answered

### What do I need besides phones?

Per pair of students: a roll of matte (frosted) tape, a few small scraps of paper and a balloon. A projector or big screen draws the room's table and boards; nothing needs printing.

### Why do both strips pull the paper?

The paper isn't charged. A charged strip shifts the paper's own charges, the other kind a little towards it and its own kind a little away, and because the near charges are closer they are pulled harder than the far ones are pushed. So T and B both pull paper, and a pull alone never tells you which kind something carries, or whether it is charged at all. Only a push does.

### What if a balloon “pushed both” strips?

The board counts it in the cross-table's corner, rings that count, and asks what else could make that happen, instead of concluding that two kinds are enough. A real push on both strips would need a third kind of charge. In a classroom it usually means the balloon touched a strip, which shares its charge so the two then push apart, or a reading went into the wrong row. Ask those students to test again in front of the room.

### Does the weather matter?

Yes. Damp air lets the charge leak away, so on a humid day more pairs show nothing, and the lesson is best on a dry one. The board shows what the room actually saw: a pair with no clear answer says so and gets no rule, the vote's question is worded from the room's own table, and the model waits for the pushes and the pull it needs. A damp room is part of the debrief rather than a failed lab.

### Why are the charges drawn as dots and rings, not plus and minus?

Because the signs are a naming convention. Benjamin Franklin called one kind positive and the other negative, and which one your T strip carries depends on the tape. The lesson draws T's kind as a dot and B's as a ring, labels its diagram as a diagram rather than a reading, and names Franklin's convention only in the model's last line.

### Which classes is it for?

Middle school and high school physical science, where students first meet electric charge and the forces between charged objects, and AP Physics 2 and AP Physics C: Electricity and Magnetism, as a lab on the two kinds of charge and polarization before Coulomb's law.

### Is there a simulation students can try?

PhET's free Balloons and Static Electricity simulation lets students rub a balloon on a sweater and watch the charges move. This lesson is the hands-on counterpart: the room's own tape and balloons are the experiment, and every rule on the board comes from what the room saw.

### What does Decka keep about the class?

Counts only: how many predicted and saw each answer for each pair, the rules the board wrote, how the vote fell with its marked answer, how the balloons sorted and the cross-table's counts. Nobody's own predictions, readings, vote or balloon are kept.

### How long does it take?

Making the strips, a round of predictions and a round of readings, one vote and the balloon test; the saved default shows under the headline as "About N min", and every timer is a setting you control before you run it.

## Run the lesson

Present the boards in PowerPoint, Google Slides and Decka. Students scan a QR code or open the session link to join from their phone browsers.
